TiePie Handyscope HS6, 4-Channel 16 Bit PC Oscilloscope Series,

TiePie

TiePie Handyscope HS6, 4-Channel 16 Bit PC Oscilloscope Series,

SKU: HS6ff

Category: Measuring Instruments

8, 12, 14, 16bit resolution, 0.25% DC vertical accuracy, 0.1% typical
Up to 1GSa/s sampling rate
Up to 250MHz bandwidth
Up to 256MSa memory per channel
Up to 200MSa/s continuous streaming
1 ppm time base accuracy
USB 3.0 compatible
Multiple scopes stackable
CMI synchronization bus for scope stacking

from

1.657,67 €

incl. 19% VAT , plus

pcs.

This item has variations. Please select the requested variation.

TiePie Handyscope HS6, 4-Channel 16 Bit PC Oscilloscope Series

This powerful USB 3.0 super speed oscilloscope combines fast sampling up to 1GSa/s with high resolutions of 12, 14 and 16bit and a large memory of 64MSa on all four channels. The oscilloscope supports continuous streaming measurements up to 200MSa/s and can be synchronized with other oscilloscopes using the CMI interface to form a multi channel combined instrument with synchronized time base. The CMI interface is available by default on the Handyscope HS6. Optionally, the Handyscope HS6 can be delivered with SureConnect connection test and resistance measurement on each channel.

By means of the supplied Multi Channel Oscilloscope Software the scope can also be used as a data logger, multimeter, spectrum analyzer and protocol analyzer.

The Handyscope HS6 is available in three different models with an extended memory option (XM), with EMI option (E) and with optional SureConnect connection test and resistance measurement (S),

furthermore there is the option of an extended warranty of 5 years instead of the standard 2 years.

HS6 Model		1000	500	200
Max. sampling rate:		1GSa/s	500MSa/s	200MSa/s
Max. streaming rate:		200MSa/s	100MSa/s	40MSa/s
Max. record length:	standard model	1MSa	1MSa	1MSa
Max. record length:	XM option	256MSa	256MSa	256MSa

SureConnect (option)

While measuring, the revolutionary SureConnect connection test feature of the Handyscope HS6 checks in real time whether your test probe or clip actually makes electrical contact with your test subject. The SureConnect option also allows dynamic resistance measurements in 14 measuring ranges from 100? to 2M?.

EMI pre compliance testing (option)

The powerful capabilities of the Handyscope HS6 - 1000XMES EMI analyzer give the user the possibility to quickly perform a good EMI compliance test. With this cost effective test, time and money are saved by avoiding extra visits to expensive EMC testing facilities. The supplied EMI probe set TP-EMI-HS6 contains three magnetic field (H field) probes and one electric field (E field) probe. The tripod ensures that the probes can be positioned properly at the object under test. Please see the picture above and note that this option is not available for all HS6 variants.

Multi oscilloscope synchronisation

The Handyscope HS6 is equipped with a sophisticated CMI synchronization bus, allowing to connect multiple Handyscope HS6s to each other by means of TP-C50H Coupling cable CMIs, to use them as a combined and synchronized oscilloscope. All Handyscopes will measure at the same sample frequency (0ppm deviation!). Apart from a synchronization bus, the CMI also contains a trigger bus and a detection bus. The maximum number of Handyscopes is only limited by the number of available USB ports.

When the instruments are located further apart, yet have to be combined and synchronized, the Wireless Multi Instrument Synchronization Module WCMI can be used. The WCMI modules are connected to the extension port of the instruments and allow to synchronize instruments that are up to 400m apart.

High accuracy

The Handyscope HS6 measures with high resolutions of 14 and 16bit. A signal measured with the Handyscope HS6 therefore has 256 times more resolution than most standalone oscilloscopes, which usually have a low resolution of 8 or 9bit. The high resolution of the Handyscope HS6 precision oscilloscope allows for measuring signals with more accuracy, because the quantization error is much lower.

Large memory

When measuring at high sample rates, a long record length/large memory is necessary to be able to record a complete signal in the acquisition buffer. Where most oscilloscopes have 2.5kSa or 100kSa memory, the Handyscope HS6 has up to 256MSa memory per channel, depending on the selected resolution and the number of active channels. When measuring at 14bit resolution and all four channels, the available memory is 32MSa per channel. This gives the user 300 to 100,000 times more memory. An advantage of a large memory is that once-only fast phenomena can be captured accurately or complete serial communication signal blocks can be measured all at once. For example complete serial communications, like CAN bus signals, can be measured all in one record to be reviewed and analyzed afterwards.

Bandwidth limit

It seems reasonable to assume that more bandwidth is better, but a wider bandwidth gives more noise. To reduce your noise you can switch on a bandwidth limiter for each channel of the Handyscope HS6.

Technical data:

Please download the datasheet for more details: Data Sheet Handyscope HS6

Download users manual: Manual Handyscope HS6

Scope of delivery:

The Handyscope HS6 is delivered with:

Instrument:	Handyscope HS6
Oscilloscope probes:	4 x Oscilloscope Probe 1:1-1:10 - HP-3250I
Accessories:	Handyscope / WiFiScope power supply, external power cable for USB port, Probe compensation cable TP-DB9-BNC-30
Software:	for Windows 10 / 11, download via website
Drivers:	for Windows 10 / 11, download via website
Software Development Kit:	for Windows 10 / 11 and Linux, download via website
Manuals:	instrument manual and software user's manuals colour printed and digital, download via website