PE-USSVM2, Ultra Stable Surface DC Voltmeter

PE-USSVM2, Ultra Stable Surface DC Voltmeter

SKU: PE-USSVM2
Category: Electrostatics
Manufacturers: AlphaLab

Measurement of electrostatics without contact

Measuring range: 0 to ±19,999.9V

Resolution: 0.1V

Analogue output

Detachable probe

2.263,38 €

incl. 19% VAT

Exp. shipping time: ca. 2-3 weeks
: 0 Workdays (Other countries)

pc.

Description
Reviews

PE-USSVM2, Ultra Stable Surface DC Voltmeter

Electrostatic meter for measuring static electricity without contact. It measures voltage on surfaces and can be used to calculate charge density on insulators. It has peak hold and a resolution of 1/10 of a volt on a 20K volt range.

Product description:
The Ultra Stable Surface DC Voltmeter Model PE-USSVM2 utilizes a sensor shutter/switcher technology which provides long term stability without drift. This technology also eliminates false or offset readings due to charged air molecules (air ions). The sensor has a 29 inch detachable cable which can be (optionally) extended up to 9'.

The meter measures the magnitude and polarity of static charge on objects or surfaces. The sensor is calibrated for measuring a surface at 1" from the end of the sensor. On metallic or conductive surfaces, the meter measures the voltage on the surface. (As with any electrostatic voltmeter, the displayed reading depends somewhat on the size of the object being measured and the distance between the object and the sensor.) On insulating surfaces, "voltage" is not a well-defined unit. In this case, the meter reads a number proportional to the static charge present.

The PS-USSVM2 has high sensitivity (resolution), and can detect even a 1/10 volt charge anywhere within its full range of +19,999.9 to -19,999.9 volts. Thus it is easy to measure whether a given process is increasing or decreasing the static electricity present, even if the increase or decrease is by a tiny fraction.

A peak hold function displays the highest positive or negative level measured since the last time that the peak hold values were cleared. The peak value is the maximum deviation from zero, and the polarity is indicated.

An analog output jack provides a DC output voltage of 0 to ±2 volts which proportionally corresponds to the display measurement of 0 to 20K volts.

An optional USB port allows readings to be recorded and uploaded to a PC. Real-time data streaming is also supported via the USB port.

With this meter, all of the following can be measured:

The amount of charge (or voltage) on surfaces and the effectiveness of antistatic processing. Measuring a tiny fractional change in the surface voltage is useful because it tells you whether the problem is getting better or worse as a new remedy is tried and modified.
The location, strength and polarity of all static sources
The approximate conductivity or ohms per square of surfaces
The approximate attractive/repulsive force between charged surfaces. (This can be calculated from the readings.)
Voltage differential through the thickness of an insulating sheet or film

Technical data:
Measuring range at 1": 0 to ±19,999.9V
Resolution at 1": 0.1V
Accuracy: ±2% of the reading
Outputs: Analogue output
                 USB (optional)
Environmental: -1°C to +43°C (30°F to 110°F), 0-90% RH non-condensing
Meter dimensions: 4.5 x 3 x 1.2 inches; 115 x 72 x 30mm
Probe dimensions: 1.2 diameter x 2.5 inches; Ø31mm x 63,5mm
Probe cable length: 29 inches; 74cm (detachable 6-pin mini DIN connector)
Weight: 5.5oz
Power supply: Battery 9V alkaline for ca. 6 hours operation (included)
                        external 9VDC power adapter (included)
                        USB port (optional). When connected to a PC/laptop power comes from the PC

Optional accessories upon request and surcharge:
+ USB port with cable
+ 6' Sensor extension cable
+ detachable rubber boot
+ hard carrying case

There are no reviews yet.